20 Trailblazers Leading The Way In Fiat Panda Key Fob Replacement

Reasons Your Fiat 500 Key Fob Won't Work

A fiat replacement key 500 key fob is a convenient way to unlock the doors and start the car. There are a myriad of reasons the fob won't work. These include a dead coin battery or water damage, receiver module issues, or interference.

This listing is for an NEW replacement fiat keys replacement Flip Key Remote that is similar to the Ilco brand. It needs to be professionally programmed (click here to find local locksmiths for your vehicle). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not working. Key fobs of today have an operating range that is limited and must be within a few inches of your vehicle to function. If you are further away from your vehicle and you press the keyfob button, it will not respond and display the message "Key Fob Not Detected".

If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a fresh one of a reputable brand such as Panasonic Duracell or Energizer. You can usually find them in your local hardware store or on the internet.

You can test the battery in the coin-cell by pressing the buttons while standing near your Fiat 500. The car will blink its parking lights and the key fob will operate the lock and unlock switches.

If the key fob doesn't function after replacing the battery, it may be damaged by water that blocks it from communicating with the receiver module in your vehicle. Water damage can happen in a variety of ways, ranging from a light splash to submerging the fob salt water at the beach. If you suspect your fob was exposed to water, put it in a dry rice bag to draw the moisture out. If this doesn't work, your fob is likely to need to be reset by an experienced auto locksmith or dealer.

Water Damage

Although the fob is equipped with rubber seals to keep water from the electronic chip inside it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can cause the circuit board to short, and eventually die. It's not a good idea to soak the fob in water however, don't give it up when you accidentally drop it in water, or fail to remove it from your pants pocket.

First take the battery off the fob. Before replacing the battery, clean the electronic chip using isopropyl or a similar product. Check the fob again to check if it's working. If the key does not function, it may need to be reprogrammed. This is usually handled by an auto locksmith or dealer.

If the key is a newer model and has not been programmed to your car, it will likely need to be replaced completely. This is a simple procedure that can be completed by a professional locksmith for automotive use. The locksmith will need to cut the key to match the ignition of your vehicle. They'll also have to reprogram the fob to the car's system. This is a fast and inexpensive process that is usually completed within the next day.

Receiver Module Issues

One of the main reasons why your 500 key fob may stop working is because it's out of range. The remote typically has 30 feet of range or less and if it's far away from your car it will not respond to your commands. You can easily solve this problem by moving the remote closer to your vehicle until it responds.

If your fob isn't working after you replace the coin battery, also known as a "button", "watch" or "button" or "button", it could be due to a problem with the circuit board inside. Reprogramming the fob typically resolves this problem. You can find directions on how to do this on the majority of automobiles by searching YouTube or checking out the owner's manual.

It is possible to replace the metal clips that hold the battery of your coin in My area place. If they loose tension, it could hinder the coin battery from being properly seated and could cause the remote to malfunction.

In rare cases the fob might be out of alignment with your vehicle because of software or hardware problems. This could be a huge issue, but you are able to usually fix it by visiting a local dealer or auto locksmith to have them reprogram your fob. In certain instances they might need to install the software again in your body control module, too.

Interference

In addition to a dead coin battery The key fob may not be able to receive or transmit signals due to interference. This can happen when the key fob is close to an electronic radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. The key fob might not function because of a problem to the buttons, water damage or damage to the internal chips.

If the key fob been unable to function for a while in the middle of the night, or after trying everything you can do at home to solve it e.g. replacing the battery, reprogramming, and using the spare key fob, you could have a malfunctioning receiver module on your 500. The receiver module, which is located beneath the dashboard, receives radio frequency signals from your key fob. It converts the signals into electronic commands, which are then interpreted by the vehicle.

Luckily, there is an easy method of resetting every single system on board in your 500 and include the key fob. Disconnect the battery 12 volt for about 15 minutes by removing the negative cable first then the positive cable. Then reconnect the battery. This will eliminate any remaining electricity, and allow you to restart the computer in your car. This will help you get your key fob to function again. If the issue persists you should seek out an expert certified technician. They will be able to determine the root of your issues.