The Most Common Mistakes People Make With Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC is an excellent choice for modern homes. They are durable, long-lasting and easy to maintain. They do not decay or rust as aluminum or timber.

It is important to clean and oil UPVC windows and doors regularly. This will help prevent costly repairs and increase energy efficiency.

1. Broken Glass

If the glass in your window is broken it can cause a huge deal of damage to your home, making it very hazardous and possibly fatal. It is important to ensure that your windows are in good working order.

Single-pane windows are fairly simple to replace and will usually fit into the frames of the past easily. However If windows with double glazing near me panes are held in place by internal beading, it'll be more difficult to get rid of the existing panes and install new ones. In this case, it is necessary to buy plastic spacers to make sure that the new pane fits into the window repairs frame.

Wearing protective eyewear and thick gloves is essential when you are planning to remove the glass by yourself. It is also recommended to lay down a drop cloth before you start working on the glass, so that any fragments of glass fall onto the cloth rather than on the floor where they can be trampled on and cause further damage.

Once the glass is removed from the window, it's best to cover the gap with packaging tape or duct tape to prevent water and drafts from entering the property until a professional can come out and repair the window. This also serves as an obstacle to stop intruders from making their way into your home. If the gap between the window and the door is substantial, you may prefer a security screen that also has an opening. This will provide the best of both.

2. Sagging

uPVC is durable, energy-efficient and affordable alternative to timber sash window. However, over time, they are susceptible to a range of issues like sagging. A window that is sagging can cause problems with light, draughts and even security. It's crucial to act immediately if you realize that your uPVC windows are sliding.

To repair a window that is sagging, you can try repositioning the hinges. To do this, you'll need open the window so that you can access the frame. Then, remove both the top and bottom hinges with a screwdriver and adjust them counter-clockwise or clockwise. Close your window to test the fit after you have relocated your hinges. If you're satisfied with the size of the window, tighten the screws to secure them in place.

If you can't reposition the hinges, you may need to replace the seal. As time passes, rubber seals lose their elasticity and become dry which causes them to loosen. It is crucial to replace your seal as quickly as you can in order to keep your uPVC window watertight and draughtproof.

uPVC handles may also become loose. Most often this is due to screws that have become loose over time. However, it could also happen because the handle mechanism has worn out. It's relatively easy to fix a loose uPVC hand. First, you'll need to shut the window and perform an initial fitting. The joints at the corners of the sash should align with the joint on the casing. If it doesn't then you can use a screwdriver to loosen the handle and return the mechanism to its original position.

3. Water Leaks

It is important to act if you get up each morning to find a smoky wall and floors that are wet. The leaks of water through windows could cause structural damage to your home and impact your ability to regulate the temperature inside your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

This is a simple fix that can be done by anyone who is a DIYer with the skills. Based on the severity of the issue the caulking that was used up may require removal before a fresh layer can be applied. It is important to remember that when it comes to uPVC window repairs, do avoid the temptation to "over-caulk and then make the area harder to clean and decrease the efficiency of your energy usage.

Make sure that the drainage holes have no debris inside them and that the sill pan is angled correctly to drain away from the window. In more severe situations, you may have to replace the window.

Other indicators of long-term water leakage are sills that are rotten and the appearance of black spots of mold on the walls near the window. This fungus thrives under damp conditions and can spread quickly throughout the house.

If the leakage is occurring between the double-glazed glass, it is more likely that the issue is more related to the seal, not the frame. Again this can easily be fixed by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or slack and blow open with a breeze it could be the hinges that are at fault. These are easily replaced by any competent DIYer and are usually completed in just a few minutes.

Almost every household in the UK will have either top hung or side hung uPVC windows that are hinged and, like all mechanical parts, they will wear out over time. Changing a window hinge is essentially a very simple procedure, but it is simpler when you have a person to help hold the frame in place.

Make sure that the uPVC hinges are closed and open in the right direction. Check for the arrows on each hinge to determine which direction the window should be opened.

The issue can be caused by opening the window incorrectly or due to a poor installation at the factory. Sending us photos through our website can often resolve the problem. We are more than happy to provide suggestions.

It is also important to lubricate the hinges on a regular basis. Applying a light engineering lubricant to the hinges is a great method of doing this. We recommend using the lubricant that doesn't contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window operate and close more easily. It can also prevent corrosion and decrease the chance of sticking. This is recommended to be done at least once a year. WD40 and other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in Upvc windows can be caused by a variety of various factors. The hinges, also because of wear and tear, may become displaced, which causes gaps to develop between the sash and the frame. If they are beyond repair, it might be required to realign them. Second, the interlock can be unbalanced. This is located on the hinge's side, and may need to be cleaned. In some cases, it may be necessary to replace these.

These seals are susceptible to wear and tear or get damaged over time, allowing air escape. Replacing these with high-quality weatherstripping will help to keep draughts at bay. Another alternative is to replace the upvc window with low-emissivity glass, this will help to regulate indoor temperatures and will reduce the possibility of draughts.

Another, and most effective ways to reduce drafts is to use an draught excluder. These are typically fabric tubes which are filled with a sort of filler and can be put on the top of your windowsill. They can keep your home warm by blocking cold air.

With a little maintenance and repairs windows made of upvc will continue to provide an excellent level of security and insulation for your home. It is important to remember that all windows will eventually become worn out, and it could be more cost-effective to simply replace them instead of fixing them. If you are experiencing issues with your upvc window it is recommended to speak with a professional as soon as you can.