10 Inspirational Images Of Double Glazing Door Lock Repairs

Double Glazing Door Lock Repairs

Is your uPVC window or door mechanism faulty? Perhaps the door or window handles aren't able to connect properly or are difficult to use.

You'll lose energy in the event that your double-glazed doors fail to perform as they should. This also increases the likelihood of burglaries. Owen the Locksmith can fix your door lock for a reasonable price.

Snapped Key

It can be frustrating when a key gets stuck into the lock. It could also be a security risk because it could expose you to a burglar if the door does not lock. Fortunately, there are quick fixes you can attempt to fix the issue and get your door operating correctly.

The first step is to remain calm. If you panic, you could end up pushing the damaged key piece further into the lock.

Next spray WD-40 or a different penetrating oil into the lock to help the broken piece slide out more easily. You can also use a screwdriver to break up any pieces stuck. If you're fortunate enough to have a bit of the key left hanging out, you can make use of a paperclip, or any other metal object with a thin surface to grab it and remove it. Both methods work, but you must be careful not to push the damaged key further into the keyway.

Some paperclips have grooved edges that could work in a pinch to extract hooks and jigsaw blades are also suitable for this purpose. If you don't have any of these handy, you can make use of needle-nose pliers that bend to create hooks. Finally, you can make use of a pair of tweezers to grab and pull out the remaining pieces of broken keys.

If you're unable to pull the broken piece of the key out, you can try using a lock de-icer. It is available in most hardware stores and is used to freeze any moisture present inside the lock.

If none of these tricks are working then it's probably time to call in locksmith. The experts at Fitlocks can quickly solve problems with uPVC door mechanisms and locks such as snapped keys and broken handles. They can also reconfigure double glazing door mechanisms so that they are easier to operate. Get a double glazing repair through us online, or give us a phone call to discuss your requirements.

Broken Cylinder

A damaged cylinder can pose a serious security threat. It's fortunately a simple repair for an expert locksmith to complete. To fix the cylinder, locksmiths will need to tap it. They can do this with the hammer or any other tools, but the most effective method is to use a long match or piece of wire. Then, put the match's tip or wire near the keyway. The locksmith will hit the lock to break it open. This is superior to using a hammer that could cause damage to the lock.

Overheating is the main cause of cylinder heads cracking. This can occur when the block and the cylinder head are made from different metals, such as cast-iron or aluminium. Different metals can heat up and cool down at different rates. This can cause localised hotspots to expand quicker than the rest of the cylinder.

Corrosion is another possible cause of cracks in the cylinder. If the head and block of a cylinder are not maintained correctly they may rust or corrode and cause them to expand more than they would normally. In time, this could cause cracks.

If your uPVC window or door lock is stiff and requires a lot more pressure to turn it could be due to a variety of reasons. This problem can result from a defective locking mechanism, or misalignment or a worn-out handle.

Fortunately, this is an easy and cost-effective fix for the majority of double glazing owners. A professional locksmith is able to solve this issue within an hour of arriving at the home. Depending on your needs they can change the locking mechanism, replace the window handles, and also change the gearboxes. A skilled locksmith will always be able to provide you with a recommendation on the most cost-effective solutions for your home. They can even recommend upgrades to high-security 3 Star TS007 euro cylinders that will give you an additional layer of security against burglars. It's a small price to pay for the security that comes from knowing your uPVC doors are safe.

Broken Handle

It's not a surprise that window handle locks can break. They have complex mechanisms which deteriorate over time. If yours is damaged it may be difficult to identify the cause of the issue and make sure you fix it correctly.

Whether the problem is in the internal locking mechanism or the latch, fixing the broken handle will improve your uPVC double glazing door's security and allow you to stop draughts. If you do not repair or replace your handle can be very costly and may damage the door's frame and lock It is therefore worth taking some time to make sure you do it right.

Screwdriver Open the window, loosen the screw holding the handle. The screw should be located on the inside of the backplate, which is usually concealed by an eye-catching cap to conceal it for aesthetic reasons. You should not lose any internal parts of the handle, such as the plates and levers on either side. Keep them in the same arrangement so that it is easier to replace them if needed.

Then, with a second screwdriver loosen the screw that connects the handle to the spindle on the back. Once this is released, you'll be capable of pulling the handle away and pull off the damaged spindle. Replace it with a brand new one, ensuring it's the same length as the previous one (you can usually find these online or in hardware stores) and screw it securely in the correct position. Don't over tighten the screw as this could damage the handle and the window frame.

Check that the new handle is installed, then close and test the handle. The hope is that it will function smoothly and you'll be able to open your window again.

While you're working on the handle, don't forget to check your upvc window repairs windows are shut correctly. If they don't close properly, you may experience damp or draughts inside your home. It could also affect the energy efficiency of your home. A local window company, like Core Sash Windows, will be able to adjust the hinges on your window doctor near me frames to ensure they are able to shut properly.

Broken Spindle

It is usually the case that the spindle in the handle is broken, not the handle itself. This is especially common with uPVC tilt-and-turn windows. These windows require a handle that operates an locking device within the frame of the window. The handle is attached to a central rod which is then activated by a series of cams that resemble mushrooms, which lock into window frame keeps. If the dead latch mechanism does not open when the handle is turned, it is possible that the spindle has broken, this can be an extremely frustrating issue.

Fortunately, there are ways to fix this problem. A good locksmith can quickly and efficiently solve the issue. A good locksmith will be able to disassemble the handle of the window by using a tool to remove the wheel from the area in which the spindle is. This can be done without causing any damage to the handle or causing any other damage to the frame of the window.

Once the wheel is removed the technician can then inspect the spindle to determine what caused it to break. This involves disassembling the spindle and examining every component, observing any damage or excessive wear. This process is usually performed by technicians in a clean environment.

Next, clean the damaged spindle. This will help get rid of any debris or dirt that may be obstructing it from functioning normally. After this, the spindle can be repaired or replaced. If it is being replaced the technician could use a dowel of a similar size to the one used in the first and drill mating holes in both pieces of the spindle. This will ensure that the new spindle has precisely matched to the handle.

If the damaged spindle cannot be repaired it may require replacement completely. Home centers can sell generic replacements, but if your window design is unusual, you will have to speak with an expert in cabinet making or woodworking who can recreate the exact part. Once the spindle has been installed, it is fixed to the handle. The screw holes on the handle with the screws that are already in the frame. Once the new handle is firmly in place, you'll be able to operate your uPVC window.