7 Easy Secrets To Totally Doing The Repairs To Upvc Windows

Repairs to uPVC Windows

uPVC is a great option for modern homes. They are easy to maintain and durable, as well as long-lasting. They do not decay or rust as aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is essential. This will reduce repair costs as well as improve the efficiency of energy.

1. Broken Glass

The damaged glass in your windows can cause serious damage to your home and may even be fatal. It is crucial to take the time to make sure that you are doing everything you can to ensure that your windows are in good repair.

Single-pane windows are relatively simple to replace and will usually fit into the frames that were previously in use very easily. If you have double-paned windows which are joined by internal beading, it is more difficult to remove and replace the old panes. In this case you'll need to locate some plastic spacers to aid the new pane in being able to fit properly into the frame of the window.

If you are going attempt to remove the glass panes yourself it is important to wear appropriate safety gear such as gloves that are thick and eye protection. It is also recommended to lay down a drop cloth before you begin working on the window panes so that any shards fall onto the fabric and not on the floor which could cause them to be trampled.

Once the glass is removed from the window, it's best to seal the gap with clear packaging tape or duct tape to prevent water and drafts from getting into the property until a professional comes out and fix the window. This also serves as a barrier to prevent any intruders from making their way into your home. If the gap is large, you may be interested in a security door that has an integrated window, since this will offer the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost energy-efficient, durable and long-lasting alternative to timber sash windows. As time passes, they may be affected by a variety of issues, including sliding. A window replacement that is sagging can cause problems with light, draughts and even security. It's important to take action immediately if you notice your uPVC windows are sagging.

To repair a window that is sagging, you can try to reposition the hinges. First, you'll need to unblock the windows so you can access the frame. Then, remove both the top and bottom hinges using a screwdriver, and then adjust them clockwise or counter-clockwise. Once you've repositioned the hinges, shut your window and test it for an appropriate fit. If you're happy with the fit, you can tighten the screws to ensure they stay in position.

If you can't reposition the hinges you may need to replace the seal. Over time, rubber seals lose their elasticity and become dry, which causes them to loosen. If this happens, it's important to replace the seal as quickly as possible to ensure your uPVC windows are watertight and safe from drafts.

uPVC handles can also loosen up. Most often, this is caused by screws that have become loose over time. However, it could be due to the fact that the handle mechanism has been worn out. It's a good thing that it's simple to repair the loose uPVC window handle yourself. First, you'll need to shut the window and do a test fitting. The corner joints of the sash must be aligned with the casing joint. If it does not then you can use the screwdriver to loosen up the handle. Then, turn the mechanism to position.

3. Water Leaks

If you're waking up to damp floors and mouldy walls each time it rains it's crucial to take action. Leaks of water from windows can cause structural damage to your home and also affect your ability to regulate the temperature of your home. The most common cause for leaks in uPVC windows is that the sealant around the frame is either damaged or missing.

This is a simple fix that can be done by anyone who is a DIYer with the skills. Based on the severity of the issue the caulking that was used up may need to be removed before a new layer of caulk can be applied. When it comes to uPVC repair, it is important to be careful not to over-caulk. This will make your window harder to clean and lower its energy efficiency.

Verify that the drainage holes are free of debris in them and ensure that the sill pan has been angled correctly to drain away from the window doctor. In more serious situations, you may have to replace the window.

Other indicators of water leakage include decayed sills and the appearance of black spots of mold on the walls near the window. This mold thrives in damp environments and is able to quickly spread throughout the house.

If the leakage occurs between the double-glazed window, it is more likely that the problem is with the seal rather than the frame. This can be easily corrected by an uPVC window specialist who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are difficult to open, or loose and blow open in a breeze It could be hinges at fault. These are easily replaced by any competent DIYer and can usually be done within a few minutes.

Most households in the UK will have top-hung or side-hung uPVC windows that use hinges and like any mechanical part they will wear out over time. The process of replacing a hinge on a window is an easy procedure, but it is easier to do when you have a person to help hold the frame in place.

Check that the uPVC hinges are open and closed in the correct direction. You can check this by looking for the arrows on each hinge, this shows which way the window should open.

The issue could be caused either due to opening the window in the wrong way or by a poor installation at the factory. This can often be resolved by sending us a photograph on our website. We will be happy to give you advice.

It is also essential to grease the hinges regularly. Applying an engineering lubricant that is light to the hinges is a great way to do this. We recommend using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window open and close more easily. It can also reduce the chance of windows sticking and help prevent corrosion. This is recommended to be done at least every year. WD40 and other solvent-based lubricants should not be used since they can damage your uPVC windows.

5. Draughts

Draughts in windows made of upvc can be caused by various factors. The hinges can also be misaligned due to wear, which can cause gaps where the sash meets frame. They can be fixed by giving them a thorough clean, however in the event that they are beyond repair it could be necessary to get them re-aligned or replaced. The interlock may be misaligned. This is located on the hinge's side, and might require to be cleaned. In some cases, it may be necessary to replace these.

These seals are susceptible to wear and tear or get damaged over time, allowing air to escape. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the window with glass that is low-emissivity, this will help to regulate indoor temperatures, and also reduce the possibility of draughts.

One of the most effective ways to reduce draughts is by using an draught excluder. These are usually fabric tubes that are filled with some kind of filler. They can be placed on the windowsill on top. They can keep your home warm by blocking out cold air.

The windows made of upvc can remain a great source of insulation and security for your home with a little regular maintenance and repairs. However, it is important to recognise that windows last for a certain period of time and eventually, they will reach a point where it is more cost-effective to replace them rather than fix them. If you are experiencing issues with your window made of upvc, it's best to consult a professional immediately.